Відео

Hay you bloody well think your out mowen and your not going to get a bit of dust in the cab...?

get a grass hopper , it's electric !

come on , man or mouse !

There is a solution for that now

Ridiculous. Even a cheaper made Grasshopper has an electric power fold deck. John Deere should be ashamed of themselves.

You need to read the comments from your last post about unsafe rotation of mowing deck. I may comment on what has worked for me since 1999. One thing I forgot to add, for people that do not know what railroad ties are or an 8 x 8 piece of lumber 18 inches long, use your car ramps.

I’m gonna try to be nice about this. The problem is solely created because of the space it requires to rotate the deck. I bought a 1435 and eight 1445 and 1999 with a 60 inch and a 72 inch side, discharge deck, respectively. For in the garage, I cut two pieces from a railroad tie (8 x 8, approximately 18 inches long.) Lift the mowing deck while approaching the garage and drive up onto the eight by eights. disembark the machine and set the chains (approximately three links) so that mowing deck cannot come down. once you have successfully used the service chains, shut off the machine. The machine was left to run, in case, you have to use the hydraulic lever to re-raise the mowing deck to catch the other service chain. I don’t have the right names for this, but, the depth gauges at the rear of the deck need to be left loose. Open the trap door (floor) and unhook the PTO shaft. Now you can rotate the deck without even removing the anti-scalping wheel at the left hand rear side of the deck. When you rotate the deck, lock it in the position so that the blades are at a 90° angle do you. There is never been a time that I wasn’t near a ditch, a curb, and embankment, and of course, there’s always loading it back on the trailer and leave it hanging off the back. I hope this resolves your problems. I still use these machines today. Almost a quarter of a century and I have no complaints. Money well spent to John Deere, and a lot of return money has been gotten with very little machinery breakdowns. Oh, and by the way, seemed as you have it in that position, make sure you sharpen the blades, balanced them, and make sure you get the grease gun out and lubricate the whole machine.

I agree rotating the deck is difficult,I only have done it once.For cleaning the underside of the deck or changing the blades I raise the deck as high as it will go and then put a couple of steel jack stands underneath so it doesn't fall on me and service it like that.

Nothing special.. Try to lift 200kg deck from 1145 whats not connecterld to tracrtor.. :)

Far cup

Omg, that's scarey.

Maybe you should buy a Kubota instead

Mine is a sweat box with AC

You are absolutely correct on your safety assessment. I completely severed my achilles tendon doing that maneuver 5 years ago. Completely changed my life. I now have a overhead electric winch in my garage which I hook to the front of the deck to lift the deck safely to latch and unlatch. Great video showing how unsafe in can be.

I agree , the attachments suck to change

Jefxhx jfffjggjggf

No that's probably not the way . But I agree you should be able to do it that way . But the seesaw effect isn't right. Needs engineered for that.

we've used these mowers for a decade.. and we've never used the service pin.. if we need under them for service they get taken off the tractor and put on a hydraulic lift.. I learned many years ago that, most salesmen would bald face lie to the pope to make a sale.. salesmens never done it.. of course he'll say its not that hard.. he wants you to buy it.. if its something really important to you, try it before you buy it You don't get a super heavy duty deck that lasts a lifetime... without it being too heavy to man handle

I've really enjoyed your videos and sympathise with you. Same issues on my 1585. I had a 1575 for eight years with never a problem. Easy to service, a quick clean after use with a cordless blower and ready for the next day. I hated getting grass blown all over me when mowing some paddocks so decided to get a 1585. Lovely to use but after 3 years the engine mounts broke. Took it to the dealer and wrote to John Deere headquarters in Queensland and they agreed to pay half of the $1350 repair bill. Two years later same thing happened. I was told they'd never heard of this problem before but the dealer said the local council brought the same model in just before me with broken engine mounts and heard from another dealer in country Victoria of the same problem. It was repaired under warranty and the dealer showed me the recall notice they'd received from Cervus Australia. Engine mounts were replaced with the same mounts on the four series tractor (which I also own) At 189 hours the cruise control failed and the transmission has gone and I can't use four wheel drive. The growling sound is noticeable in reverse but ok in forward gear. Dealer said use two wheel drive which has no transmission noise but it has made my mowing of 30 acres restricted when on slopes. I've just ordered a new 1585 and hopes whoever goes to buys my old machine and reads the required previous owners info that they give me a call. I'm sure the dealer will repair any faults before reselling. Managed to get $36k trade in, not too far off what I paid 6 years ago.

Theese new john deeres are built like shit, everything is skinier and with plastis. This should be the top of the line but the old 1145 looks like tank compared to this

Looks like a 30sec deal if ya quitcher bitchin

should have got one of the new toro 3200/3300 groundsmaster

I’d love to hear some of your thoughts on the corona virus pandemic.......

How has it been since? More things that have broken?

ever heaerd of a lever bar. and take the drive shaft off period

As usual you make a great point and ofc mate you're bloody right ! However nobody likes a whinger.. I'm a fan ofc... yo make these videos just because you can right 🤣🤣🤣🤣 lol Great

Mate.. come on .. it's not unbelievable at all ! It always happens.. get of ya arse and blow the bloody hell out of it once in awhile..

You have a point mate.. we have to blow out the whole machine 3 or 4 times a day here in New Zealand .. just the way it is in summer. We'll do 1000 hours a year on em mate.. bloody bonza 🤣 you're right about being a fantastic product just get John Deere to tidy up those few issues.. ooh and build a bloody decent drive shaft too... their one's are crap.. only last about 600 hours if you're lucky then they'll cause vibration.. 😉 but l have to say we cut much longer and thicker grass than the stock drive shaft was designed for ... Btw.. l have a contact for a really strong DS ofc. Cheers

Lol mate I get your sense of humour !! I've done all this myself ofc and l agree it's bloody stupid ridiculous system.. and your reason for the video is to make this point.. l appreciate that you do it a different way when we're not watching ha haha of you do ! Same as me huh brother...🤣 Btw l love the language.. Lol fantastic video.. well done my mate !! 😎

Put a jack stand under the front of the mower and stop whining.

You are funny.

Btw how have you found the cut quality of this machine? Does it handle super thick aussie grass and still cut ok?

What a fucking joke. Im considering uprading to a 1570 or 1580. I was told you didnt even have remove the pto shaft by the sales rep. I'll be getting him to show me how easy it is after watching this. I'll have to do this everytime I need to load the machine onto my trailer as its too long with the deck down. God I hope theres an easier way.

ua-cam.com/video/e0OieBPW-R0/v-deo.html

must have bought it from an irish dealership